Engine Service Tools

Kit includes: Camshaft positioning tool, camshaft holding tool, crankshaft positioning tool, secondary chain tensioner tool.  Saves time; all tool...

This kit contains the tools to remove and install inner cam bearings without damage to the crankcase. The bearing puller is designed to trap the n...

Ford 3.5L 4V V6 engines used in 2007-2012 Edge, MKZ, 2007-2009 MKX, 2008-2012 Taurus, Taurus X, Sable, 2010-2012 Fusion, 2010-2012 MKZ, MKS, MKT, ...

Clamshell type piston ring compressor, 5.40" diameter. Assures proper piston installation, reducing the possibility of broken rings. Works on sele...

Save time removing crankshaft rear seals, preventing damage to the block and crank. This seal remover is a special puller with three jaws designed...

Ensure replacement injectors and seals are installed correctly. This kit installs the dual seals onto the end of the injector. These seals must be...

Oil seal and wear ring installer for 5.0 inch diameter seals Makes the difficult job of correctly installing the rear crankshaft seal and wear rin...

Easily diagnose engine oil system issues. This adapter installs in place of the spin-on oil filter to allow existing oil pressure gauges to be att...

Tool is used to properly hold the cam gear stationary while removing/installing the cam gear retaining bolt without damage. The tool installs into...

Allows the crankshaft pulley and/or harmonic balancer bolt to be broken loose Includes tool necessary to properly counter the rotation of the cran...

Designed for use on Ford 1993–2004 4.2L, 4.6L 2-valve, 4.6L 4-valve, 5.4L V8, and 6.8L V10 engines when installing timing chains These engines are...

Now you can have the proper-size driver for nearly any automotive seal, bearing, or bushing installation job. These sets include discs and handles,...

This set contains discs and handles that can be assembled into a pilot, a spacer, and a driver. Designed for bearing, seal, & bushing install...

Works on 1994-2003 7.3 diesel engine in Ford 3/4-and 1-ton trucks A complete kit with the tools you need to properly remove and install the rear m...

This installer works on crankshaft rear oil seals that come with or without a metal wear sleeve. Designed for use on 1993-1997 Aerostar or 1993-201...

Oversized retaining plates lock camshafts together at top dead center (TDC) on General Motors 2.8L 3.0L and 3.6L DOHC engines Three-plate set is u...

Unique design helps prevent breakage by locking the plug porcelain core to the plug hex allowing it to turn as one complete unit. Will also pull p...

Belt tension gauges are used to properly check drive belt tension on drive belts to ensure maximum belt and bearing life. Scale reads 30 - 180 inc...

Ford 4.6L 3V V8 engines used in 2005-2010 Mustang, 2006-2010 Explorer, 2009 F-Series trucks Ford 5.4L 3V V8 engines used in 2004-2012 F-Series, 20...

Comprehensive tool kit designed to save time when servicing GM 4-cylinder engines. Tools are actually easier to use than the original OE essential...

This special set of sensor sockets covers sensor application found on todays vehicles to provide easy removal and installation of hard to reach sen...

Allows for engine oil pressure to be measured. Installs in place of oil filter providing ports to attach oil pressure tester. Dual port for bottom...

Required tools to adjust and hold cam shaft timing on General Motors 3.0 and 3.2 V-6 engines Kit is designed to save shop time when servicing Gene...

Works on Ford 1.6L 4V L4 engines used in 11-12 Fiesta 3 Tools