Engine Service Tools

Cast Aluminum End Cap Wrenches and Cold-Headed Steel Sockets that Fit Most Popular Domestic and Import Vehicles. Low profile 6 point socket sizes ...

Use for install & removal of crankshaft rear main seal & wear sleeve. Applications: Cummins ISX, QSX, ISX15 & ISX12. Fits the newest C...

Use for aligning the camshaft to TDC (Top Dead Center). Packed in an EVA insert blow mold case for organized storage. Applications: Mercedes Benz ...

Kit includes: 3762 - Porsche Cam Turning Wrench that has a deep double-D shape cavity for servicing classic models. It is required for countering ...

Use for aligning the camshaft timing angle to correct position. Services Mercedes Benz (60°) V6 engine from 2011-2019. Compare to Mercedes Benz Fa...

Used for replacing the fuel injector Teflon seals on General Motors 2.0L & 3.6L engines with Hitachi fuel injectors [2010-2017] and 2.0L, 2.4L...

Use with Diesel Compression Tester TU-15. Injector adapter with quick disconnect for Caterpillar 3196 engines.

Forged oil filter adapters for VW, Audi, Porsche, Mercedes Benz. Drive with 1/2" sq. drive or a box wrench Heavy duty thick wall  Heat treated al...

This Tool is used to extract the broken porcelain or seized sleeves from broken spark plugs in 2003 to current Ford Triton Engines. In some cases t...

Required to hold the flywheel in a secure position while servicing the balancer retaining bolt This tool allows for securing the flywheel by utili...

Kit includes specialty tools required to perform timing service and repair. Use to accurately locate TDC for servicing and repairing head gasket a...

22" (55cm) long, special angled wrenches service serpentine belts on Mini's with N12, N14, N16 & N18 engines. Each wrench features different 1...

Use for 3.9L, 5.9L & 6.7L Cummins engines when wear sleeve is installed or replaced Services Paccar PX-6, 1989-2016 Cummins 4BT 3.9L, B Series...

Tool mounts to the front of the block, its tabs engage both cam phasers to be held in place so the Phaser bolts may be serviced. The ECOTEC engine...

Use this camshaft alignment tool on the upgraded 3.5L Ford EcoBoost engine Applications: Expedition (2018-2019), F-150 (2017-2019), Ford GT (2017-...

Specially designed to position the camshafts in TDC position Slackens and tightens the bolts attached to the camshaft gears Compare to Mercedes Be...

Set includes sizes: #1730 - 5/8” x 12 PT (OAL: 6”) #2380 - 5/8” x 6 PT (OAL: 10”) #2390 - 9/16” x 6 PT (OAL: 10”) #2394 - 14mm x 6 PT (OAL: 10”) ...

Removes and installs water pump pulley on 3.0L DOHC engine. Includes: Forcing screw with shaft protector and cross block puller, pulley removal pl...

Removes harmonic balancers without tapped holes. Services V6 & V8 GM (5.3L, 5.7L 6.0L, 6.2L & 7.0L), Chrysler, Dodge & Jeep (3.5L, 3.7...

For removal and installation of Spark Plugs, Glow Plugs & Pressure Sensor Glow (PSG) Plugs. Included sizes: 8mm x 6-point, 9mm x 6-point, 10mm...

Services newer Dodge/Chrysler/Jeep models with Pentastar VVL 3.6L engines. Compare to Dodge/Chrysler/Jeep factory tool #: 2025002090. Applications...

This tool is used to remove and install belts on serpentine belt systems using the spring loaded idler pulley. For applications with limited acces...

Simplifies valve adjustment on 2004 to 2013 DT466 & MaxxForce International Engines. 13930 & 13940 are both required. Two into One design ...

For loosening the tension on the timing chains during camshaft and Phaser service procedures. Applications: 2011 and newer Chrysler, Dodge & J...